|
| |
|
| |
|
|
Machining of titanium alloys
Müller, Peter ; Sliwková, Petra (referee) ; Píška, Miroslav (advisor)
The bachelor thesis specifies the most important properties and production processes of titanium, categorizes titanium alloys and their properties. In the experimental part, titanium alloy Ti-6Al-4V blank was machined and cutting forces were measured, depending on selected feeds per revolution. Subsequently specific cutting force was calculated and compared with values given by the tool manufacturers.
|
|
|
On the milling of ceramic materials
Rudel, Václav ; Slaný, Martin (referee) ; Píška, Miroslav (advisor)
In the diploma thesis dividing of ceramic materials is made, their bonds and other attributions, which define ceramic materials. There is also described how ceramic materials are manufactured and the thesis is including information about machining ceramic materials. In the experimental part sample of ceramic material R-S67K was machined by milling. During the experiment cutting forces were measured and roughness of surface after finishing, these data were finally evaluated.
|
|
|
Testing of cutting parameters for UMCo50 machining
Jakubec, Thomas ; Kolomý, Štěpán (referee) ; Zemčík, Oskar (advisor)
The diploma thesis deals with the machinability of materials, the theoretical part describes the factors that have a dominant influence on machinability. The basic aspects according to which the machinability of the material and the wear of the tool are determined are also given here. The distribution of cobalt alloys is given here, including the UMCo-50 alloy, which is the subject of experimental research. It is an alloy for high-temperature use with good abrasion resistance and is used especially where other materials lose their mechanical properties due to the high temperature. The practical part followed the thesis of my colleague Ing. Peter Prno [1], which due to lack of time could not measure all the necessary quantities, resp. course of back wear for the remaining two cutting speeds. During the experiment, the wear of the tool back was monitored as a function of time at different cutting speeds in turning technology. The main goal was to determine the resulting tool life at the remaining cutting speeds and thus obtain a more accurate Taylor dependence. The turning forces, the quality of the machined surface and the formation of chips were also monitored during turning.
|
|
|
Cutting performance of very fine grained end mills
Uttendorfský, Aleš ; Humár, Anton (referee) ; Píška, Miroslav (advisor)
This diploma thesis consists of two parts. The theoretical part describes sintered carbides, their properties and manufacturing tools. Some selected problems of milling and its physical nature is discussed also. It also deals with the types and methods of tool wear testing. The aim is to compare the experimental properties of monolithic end milling cutters (short four cutting edges, uncoated carbides) of various grain sizes in two basic ways of milling - down-feed method and up-feed method. The measured values are evaluated by analysis in time series of the cutting forces and power.
|
|
|
Simulation verify the dynamic behavior of the portal machine tool
Danda, Libor ; Holub, Michal (referee) ; Vetiška, Jan (advisor)
This bachelor thesis deals with summary of simulation software for the simulation of the dynamic behavior of machines, creating a simulation model of the machine in MSC.ADAMS and experimental measurement of cutting forces. It also deals with dynamics simulations axis motion and deformation analysis of selected components of the machine. Finally, they are designed to be structural adaptations in order to increase the dynamic stability of the machine.
|
|
|
Implementation and application of the edge-material pair methodology at orbital drilling
Saillet, Alan ; Sliwková, Petra (referee) ; Píška, Miroslav (advisor)
This internship's objective is to implement modeling of uncut chip thicknesses and milling forces in 3-axis milling, and apply it to orbital drilling. The goal is to understand deeper the process, and develop a tool which permits to model a wide range of end-mill tool geometries, and most of 3-axis milling operations.In this report, the following axis will be developed: • The modeling of the complex tool geometry • The modeling of uncut chip thicknesses in slot milling, and for any 3-axis milling operation • The strategy which has been chosen to identify cutting forces coefficients, and their use. • The obtained results and prospects for development.
|
|
|
Cutting forces when milling fibre reinforced composites
Martének, Libor ; Forejt, Miloslav (referee) ; Humár, Anton (advisor)
The thesis is focused on composite materials with a view to their classifi-cation, identification, usage, current trends in production and development and possibilities of effective machining. As a part of this thesis, there is an evaluation of experimentally measured values during technological testing of milling of a fibre reinforced composite with a polyester matrix reinforced by fiberglass. The technological testing was performed with a view to measure certain values, i.e. impact on machined material, working conditions for a tool and its abrasion equal to the values of components of cutting force. From the values obtained from the testing, a general analysis of cutting force when milling was created containing overall technical and economical evaluation.
|
|
|
On the cutting performance of selected HSS drills
Med, Slavomír ; Dvořáková, Jana (referee) ; Píška, Miroslav (advisor)
The bachelor thesis aims on a twist drill. In the theorical part characterizes the parts of drill bit and presents its fabrication from fabrication of cutting material to coating. This part finishes by description of contemporary methods of measuring of cutting performance. The main goal of this thesis is to propose and realize measuring of cutting performance of which results we can compare selected HSS drill bits and recommend them to practice. The tests are described in the practical part which contains the evaluation of results too.
|
guest ::
